Flat Tension Bracing

Pre-punched galvanised steel tension brace designed to brace timber wall frames in domestic construction.
This pre-punched galvanised steel brace is:
Very useful in situations where bracing cannot be cut into studs.
The ideal tension bracing system when used in conjunction with a Multi-Tensioner.
Practical - it helps reduce on-site labour time as studs do not have to be notched!
APPLICATION
Two individually cut pieces of Flat Tension Bracing are required to brace a timber framed wall section. These pieces should overlap to form an ‘X’.
- Secure first end of one piece of bracing into position using 30mm x 2.8Ø Multinail nails.
- Stretch the Flat Tension Bracing over the entire panel to be braced, ensuring the brace is taut.
- Secure the second end while maintaining tension on the brace.
- Repeat this procedure for the second piece of Flat Tension Bracing, ensuring an ‘X’ is formed.
- Secure the Multi-Tensioner in each length of Flat Tension Bracing to remove any remaining slack.
- Fix T-Plate, Stud Tie or Nail On Stud Tie as required (refer individual Multinail product brochures).
Please use the relevant Standards to determine the number, location and tie-down of bracing units. Bracing capacities stated are relevant for wall heights up to (and including) 2.7m. For wall heights greater then 2.7m, please refer to AS1684.
TYPICAL USE - 1.5kN/m
1.5kN/m Bracing Capacity as per AS1684 Residential Timber-Framed Construction, Table 8.18(b)

No Stud Ties required for 1.5kN/m Bracing Capacity as per AS1684 Residential Timber-Framed Construction, Table 8.18(b)
Detail A


DESIGN LOADS
Size(mm) | Tension Capacity (kN) |
---|---|
30 x 0.8 | 5.6 |
TYPICAL USE - 3.0kN/m
3.0kN/m Bracing Capacity as per AS1684 Residential Timber-Framed Construction, Table 8.18(d)

Detail B

DESIGN LOADS
Size(mm) | Tension Capacity (kN) |
---|---|
30 x 1.0 | 6.5 |
SHORT WALL BRACING
- Wrap ends of Flat Tension Bracing around plate and fix with nails (Refer Detail B)
- Attach minimum 30 x 1.0 Flat Tension Bracing with 2/30mm x 2.8Ø Multinail nails into each stud
- Multi-Tensioner
- Minimum 70 x 35-F5 Wall Stud
- Stud Ties or 1/T-Plate (both sides of frame)
- Tie-down as per AS1684/minimum M10 Concrete Screw Anchor

DESCRIPTION AND PACKAGING
Manufactured from 30 x 0.8mm / 30 x 1.0mm Galvanised G300 Z275 Steel
Description | Product Code | Reference Code | Quantity | Kg. |
---|---|---|---|---|
30 x 0.8mm - 10m Roll | TA501 | FTR3001008 | 1 | 2.4 |
30 x 0.8mm - 20m Roll | TA502 | FTR3002008 | 1 | 4.8 |
30 x 0.8mm - 30m Roll | TA500 | FTR3003008 | 1 | 6.0 |
30 x 0.8mm - 50m Roll | TA503 | FTR3005008 | 1 | 10.0 |
30 x 0.8mm - 100m Roll | TA504 | FTR3010008 | 1 | 21.6 |
30 x 1.0mm - 3.15m Length | TA555 | FTL3031508 | 250 | 128 |
30 x 1.0mm - 3.35m Length | TA556 | FTL3033510 | 250 | 136 |
30 x 1.0mm - 3.60m Length | TA557 | FTL3036010 | 250 | 146 |
30 x 1.0mm - 3.90m Length | TA558 | FTL3039010 | 250 | 158 |
30 x 1.0mm - 4.20m Length | TA559 | FTL3042010 | 250 | 171 |
30 x 1.0mm - 10m Roll | TA551 | FTR3001010 | 1 | 2.5 |
30 x 1.0mm - 20m Roll | TA552 | FTR3002010 | 1 | 4.9 |
30 x 1.0mm - 30m Roll | TA550 | FTR3003010 | 1 | 7.3 |
30 x 1.0mm - 50m Roll | TA553 | FTR3005010 | 1 | 12.2 |
30 x 1.0mm - 100m Roll | TA554 | FTR3010010 | 1 | 24.5 |
NOTE: The 100m Roll requires a special floor-mounted Bulk Coil Dispenser. | ||||
Please contain Multinail for more information. | ||||
Multi-Tensioner Including wing nut and washer (TA0424) | ||||
30mm x 2.8Ø Multinail Nails (TA302) |
